View TWR-K60N512_4935581.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Quick Start Guide for TWR-K60N512
TOWER SYSTEM
TWR-K60N512
Low-power MCU with USB, Ethernet and security
TOWER SYSTEM
Get to Know the TWR-K60N512
Primary Connector Infra-red General Purpose Tower Plug-In (TWRPI) Socket SW3 (Reset) Power/OSJTAG Mini-B USB Connector Secondary Connector
Figure 1: Front Side of TWR-K60N512 Module Not Including TWRPI.
SW1 SW2 Touch TWRPI Socket LED/Touch Buttons E1-E4 MK60N512 VMD100 Microcontroller MMA7660 Accelerometer
TWR-K60N512
The TWR-K60N512 microcontroller module is part of the Freescale Tower System, a modular development platform that enables rapid prototyping and tool re-use through reconfigurable hardware. Take your design to the next level and begin constructing your Tower System today by visiting freescale.com/tower for additional Tower System microcontroller modules and compatible peripherals.
Quick Start Guide for TWR-K60N512
TOWER SYSTEM
Potentiometer
SD Card Socket
VBAT (RTC) Battery Holder
Figure 2: Back Side of TWR-K60N512 Module.
TOWER SYSTEM
Step-by-Step Installation Instructions
In this Quick Start Guide, you will learn how to set up the TWR-K60N512 module and run the default demonstration.
STEP
1
Install the Software and Tools
STEP
Install the P&E Micro Kinetis Tower Toolkit to install the OSJTAG and USB-to-Serial drivers. These can be found on the DVD under Software.
Tilt the board side to side to see the LEDs on E1-E4 light up as it is tilted. While the board is held flat, touch the pads on E1-E4 to toggle the LEDs.
3
Tilt the Board
STEP STEP
Install the included battery into the VBAT (RTC) battery holder. Then, connect one end of the USB cable to the PC and the other end to the Power/ OSJTAG mini-B connector on the TWRK60N512 module. Allow the PC to automatically configure the USB drivers if needed.
2
Configure the Hardware
4
Play the Memory Game
Press SW2 to play a memory recall game using the touch pads E1-E4. A sequence will light up, and then press the touch pads in the order flashed. If an incorrect sequence is touched or you take too long, all the lights will blink rapidly and the game will reset. Press SW1 to go back to the accelerometer demo.
Quick Start Guide for TWR-K60N512
TOWER SYSTEM
Explore Further by Conducting Lab 1: TWR-K60N512 Quick Start Demo
STEP
5
Explore all the features and capabilities of the pre-programmed demo by reviewing the lab document located at freescale. com/TWR-K60N512.
Learn More About the Kinetis K60 Microcontrollers
STEP
6
Find more MQX and bare-metal labs and software for the Kinetis K60 microcontrollers at freescale.com/TWR-K60N512.
TOWER SYSTEM
Jumper Options
The following is a list of all the jumper options. The default installed jumper settings are shown in bold.
Jumper J8 Option MCU Power Connection Setting ON OFF 1-2 2-3 Description Connect on-board 3.3V supply to MCU Isolate MCU from power (connect an ammeter to measure current) Connect VBAT to on-board 3.3V supply Connect VBAT to the higher voltage between on-board 3.3V supply or coin-cell supply Connect main EXTAL to on-board 50 MHz clock Connect EXTAL to the CLKIN0 signal on the elevator connector OSJTAG bootloader mode (OSJTAG firmware reprogramming) Debugger mode
J9
VBAT Power Selection
J6
Clock Input Source Selection
1-2 2-3
J10
OSJTAG Bootloader Selection
ON OFF
Quick Start Guide for TWR-K60N512
TOWER SYSTEM
Jumper J12
Option JTAG Board Power Connection
Setting ON
Description Connect on-board 5V supply to JTAG port (supports powering board from JTAG pod supporting 5V supply output) Disconnect on-board 5V supply to JTAG port Connect PTD7/CMT_IRO to IR Transmitter (D507) Disconnect PTD7/CMT_IRO from IR Transmitter (D507) Connect USB0_VBUS from Elevator to VREGIN Disconnect USB0_VBUS from Elevator to VREGIN
OFF J2 IR Transmitter Connection ON OFF J1 VREGIN Power Connection ON OFF
TOWER SYSTEM
To learn more about the TWR-K60N512 and other Freescale Kinetis microcontroller products, please visit freescale.com/TWR-K60N512, freescale.com/Kinetis and freescale.com/Tower.
Freescale, the Freescale logo and CodeWarrior are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. Flexis, Kinetis and Processor Expert are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) 2010 Freescale Semiconductor, Inc.
Doc Number: TWRK60QSG / REV 0 Agile Number: 926-78535 / REV A

▲Up To Search▲

Price & Availability of TWR-K60N512

	To Download TWR-K60N512 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .